AI News

When automakers are rushing to develop their own batteries, why is IM going the opposite way?

LeiphoneUpdated Nov 16 18:49

AI summary

The upcoming IM LS8 NEO pure electric version uses CATL batteries across the entire range, from cells to battery packs, in contrast to the route of automakers such as Xiaomi and Li Auto that develop their own batteries. The new car offers two specifications: a 93kWh lithium iron phosphate battery and a 103kWh ternary lithium battery, is based on an 800-volt dual silicon carbide platform, has a peak charging power of 396 kilowatts, and comes standard across the range with the Lizard 3.0 full-wire-controlled chassis.

Body · AI translation

The power to define products built around batteries is becoming a focal topic in the industry.

Xiaomi and Li Auto recently launched their own battery brands, teaming up with battery makers such as Sunwoda and CALB, declaring automakers' determination to go deep into battery R&D and manufacturing. Li Xiang said, "The world needs both battery companies that understand smart electric vehicles best, and smart EV companies that understand batteries best."

CATL Chief Manufacturing Officer Ni Jun put it bluntly: "Professionals should still do professional work."

Some are turning to in-house development, while other automakers insist on equipping their entire lineup with CATL batteries. In the upcoming new car from IM Motors, the IM LS8 NEO pure electric version, everything from the cells to the battery pack uses CATL batteries.

They believe that handing the battery to a top-tier supplier is about entrusting the hardest and most error-intolerant link in the whole vehicle to certainty.

Recently, Leiphone conducted an on-site visit to a CATL factory, where we also saw how a good battery cell is produced.

Tang Guocheng, CATL's senior product engineer for domestic passenger vehicles, noted that the battery field has a barrel effect: how far and how long an electric car can run is not determined by the best of the hundreds or thousands of cells in the battery pack, but by the worst one.

CATL's entire cell production process has more than 7,000 quality control points; on the production line, multiple high-precision CCD cameras are deployed after each winding process, working with AI for real-time inspection, increasing defect recognition speed by 300% and reducing the need for manual re-inspection by 70%. Therefore, CATL has always insisted on defining its quality control standard at one in a billion, that is, a PPB-level failure rate.

Among these, the cells are produced at the Ningde base and the Liyang base. In the parts industry, the Ningde base was the first production base to be selected as a Lighthouse Factory.

The upcoming model's cells come from CATL's Lighthouse Factory, and it is equipped with two specifications of CATL batteries: a 93kWh lithium iron phosphate battery and a 103kWh ternary lithium battery.

The batteries offered come in two specifications: a 103kWh ternary lithium battery and a 93kWh lithium iron phosphate battery.

The 103kWh ternary lithium battery has less range and power degradation in northern winters. At the same time, it has high-rate discharge capability, still delivering high power at -20°C in a low-battery state to meet daily power needs;

As for the 93kWh lithium iron phosphate battery, through innovative cell material design, it improves the conduction speed of lithium ions in low-temperature environments, and combined with the H03 battery pack design, enables the battery pack to achieve a 95% capacity retention rate at -20°C, so users no longer need to worry about low-temperature range degradation. This battery is equipped with CATL's all-new generation BMS platform, with state-of-charge estimation accuracy reaching 3%, solving the historical pain point of range jumping in traditional lithium iron phosphate batteries.

Inside the battery pack, CATL has also configured an intelligent active fuse with a built-in ignition tube device. When the BMS detects dangerous signals such as thermal runaway or a collision, it can respond within milliseconds and cut off the high voltage. A traditional fuse takes about 10 seconds from short circuit to cutoff.

Both battery packs use the hardware foundation of an 800-volt dual silicon carbide platform, with peak charging power of up to 396 kilowatts, compatible with more than 90% of public charging piles on the market.

On IM Motors' side, the new car comes standard across the lineup with a steer-by-wire chassis. The Lizard 3.0 full steer-by-wire chassis consists of steer-by-wire, bidirectional 24-degree rear-wheel steering, CDC dampers, air springs and wet brake-by-wire. The turning radius is only 4.85 meters, comparable to a German A0-class sedan.

Not only is it easy to drive, the Lizard chassis also ensures driving safety. Through coordinated control of braking, steering and suspension, the LS8 NEO pure electric reduces roll angle by about 33%, doubling anti-roll performance compared with traditional vehicles.

Ding Yi, senior expert in IM Motors' chassis systems, told us that IM Motors' proprietary technology can bring the vehicle to a safe stop using only the rear-wheel steering and braking system even when the power supply, controller and sensors all fail.

In 2017, SAIC and CATL jointly established two companies with a clear division of labor: CATL-SAIC Power Battery Co., Ltd. makes cells, and SAIC-CATL Power Battery System Co., Ltd. makes power battery systems (PACK).

The joint-venture chess game set up nine years ago has now landed its move on the LS8 NEO. While others debate "who understands batteries better," IM Motors' choice is: give the power of definition to nine years of symbiosis with a top-tier supplier, and leave certainty to users. The endgame of the battery war may not be who replaces whom, but each of the diverse routes proving itself. Above the bottom line of safety, all roads lead to Rome.

Source

Leiphone